The 18th Shanghai International Automobile Industry Exhibition - FENG-YI

The 18th Shanghai International Automobile Industry Exhibition

354pcs FYL DLB Motor Winch Kinetic LED Tube(120cm long led tube, motor winch ...

354pcs FYL DLB Motor Winch Kinetic LED Tube(120cm long led tube, motor winch with 3m lifting stroke distance) were installed at the top of the VENUCIA Booth in the 18th Shanghai International Automobile Industry Exhibiton, created a unique and spectacular visual sense of 3D moving effect which attracted many visitors.

Brief Introduction of 18th Shanghai International Automobile Industry Exhibition:

The 18th Shanghai International Automobile Industry Exhibition (hereinafter referred to as: Shanghai auto show 2019) is an auto show sponsored by China Automobile Industry Association, Shanghai Branch of China Council for the promotion of international trade and auto industry branch of China Council for the promotion of international trade. With the theme of “creating a better life together”, the auto show will focus on the innovative development achievements of the world automobile industry, Sing the theme of “better life” again.

From April 18 to 25, 2019, the 18th Shanghai International Automobile Industry Exhibition will be held in the National Convention and Exhibition Center (Shanghai).

More than 1000 well-known domestic and foreign enterprises from 20 countries and regions participated in the 2019 Shanghai auto show, with a total exhibition area of more than 360000 square meters. All 12 indoor pavilions of the National Convention and Exhibition Center (Shanghai) were opened, including 9 passenger car pavilions (1H, 2h, 4.1h, 5.1h, 6.1h, 7.1h, 7.2h, 8.1h, 8.2h); One Pavilion (3H) for commercial vehicle exhibition area and future travel zone; There are two pavilions (5.2h, 6.2h) in the auto parts exhibition area. In addition, interactive experience area, rest room, clinic and other functional and service areas are set up in the museum. It is very convenient and economic that our DMX winch matched for our different pendents under its lifting capacity. FYL will gradually updating newest pendents for your more choice in different times.

Recommended for you
US New York -A Lighting Revolution at the Childish Gambino’s The New Would Tour-Kinetic Bar
US New York -A Lighting Revolution at the Childish Gambino’s The New Would Tour-Kinetic Bar
South Korea Seoul -Got7 concert-Kinetic Bar
South Korea Seoul -Got7 concert-Kinetic Bar
Beijing China-CCTV 2019 China Music Awards-Kinetic Bar
Beijing China-CCTV 2019 China Music Awards-Kinetic Bar
South Korea-BTS's "Boy with Luv" performance-Kinetic Bar
South Korea-BTS's "Boy with Luv" performance-Kinetic Bar
Prdoucts Categories
FAQ
Wedding & Parties Lighting Solutions
What about after-sales support and training?

On-site training + remote technical support, spare parts availability, and annual inspections. Service Level Agreements (SLAs) for maintenance services are available.

Wholesale Cooperation
What is the restocking cycle for wholesale customers? Can production be prioritized?

The restocking cycle for standard models is 3-7 days (same-day shipment if stock is sufficient), and the restocking cycle for customized models is the same as the initial customization cycle (15-45 days). For annual cooperative customers (with an annual purchase amount of ≥ 500,000 RMB), a "priority restocking agreement" can be signed, and 10%-15% of safety stock will be reserved to ensure emergency restocking needs are met within 3 days.

Products
The X/Y axis moves abnormally (jitter, no response). What causes this?

Address the issue as follows:

1. Mechanical Check: Open the fixture (after power-off) to inspect if the X/Y axis belts are loose or broken; re-tighten or replace belts if needed.

2. Optical Coupling Calibration: Enter "Settings → Motor Calibration → X/Y Axis" to adjust the offset (-128~+127) or enable "Optical Coupling" (auto-corrects step loss).

3. Reset & Restart: Press "Menu → Reset → XY Reset" to reposition the axes; if no response, check the X/Y axis photoelectric switches (replace if "X/Y Hall Error" appears in the error menu).

The fixture overheats and shuts down. What should I do?

Resolve overheating issues:

1. Environment Check: Ensure the operating temperature ≤60℃; move the fixture away from heat sources (e.g., stage heaters) and ensure 50cm clearance around the fan grille.

2. Fan Maintenance: Clean the fan and fan grille with compressed air (remove dust buildup); check if the fan runs when the fixture is powered on (replace fan if silent).

3. Protection Threshold: Enter "Settings → Temperature Protection" to adjust the threshold (default 60℃, max 80℃) if the environment requires higher operating temperatures.

Want to learn more about the latest updates?

Have questions or ready to illuminate your project? Reach out to our expert team today.

Please enter your name not exceed 100 characters
The email format is not correct or exceed 100 characters, Please reenter!
Please enter a valid phone number!
Please enter your field_1233 not exceed 150 characters
Please select What you're interested in
Please enter your content not exceed 3000 characters

Rest assured that your privacy is important to us, and all information provided will be handled with the utmost confidentiality.

By clicking "Send your message," I agree to your processing my personal data.
To see how to withdraw your consent, how to control your personal data, and how we process it, please see our Privacy Policy and Terms of Use.

Contact customer service

How can we help?

Hi,

We value your needs and feedback. For any inquiries, contact us—we're here to help with expert support. Fill in the details below, and our team will get back to you promptly.

×
Please enter your name not exceed 100 characters
The email format is not correct or exceed 100 characters, Please reenter!
Please enter a valid phone number!
Please enter your field_1233 not exceed 150 characters
Please select What you're interested in
Please enter your content not exceed 3000 characters

Get a free quote

Hi,

Call us to discuss more on your own project!

×
Please enter your name not exceed 100 characters
The email format is not correct or exceed 100 characters, Please reenter!
Please enter a valid phone number!
Please enter your field_1233 not exceed 150 characters
Please select What you're interested in
Please enter your content not exceed 3000 characters

Get the solution

Hi,

Call us to discuss more on your own project!

×
Please enter your name not exceed 100 characters
The email format is not correct or exceed 100 characters, Please reenter!
Please enter a valid phone number!
Please enter your field_1233 not exceed 150 characters
Please select What you're interested in
Please enter your content not exceed 3000 characters

Send my request

Hi,

Call us to discuss more on your own project!

×
Please enter your name not exceed 100 characters
The email format is not correct or exceed 100 characters, Please reenter!
Please enter a valid phone number!
Please enter your field_1233 not exceed 150 characters
Please select What you're interested in
Please enter your content not exceed 3000 characters